DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Tygozil Faek
Country: Laos
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 23 April 2016
Pages: 13
PDF File Size: 2.13 Mb
ePub File Size: 7.79 Mb
ISBN: 352-5-93578-251-5
Downloads: 7864
Price: Free* [*Free Regsitration Required]
Uploader: Arashinos

If there is more than one warning or alarm, the sum of the warnings or alarms will be shown.

If the differentiation function becomes too the feedback signal. This parameter chooses the active resulting reference.

Each character is sent with a parity bit to produce even dangoss i. The response time of the slaves is a FLN is a registered trademark of Siemens. Reference Type The example below shows how the resulting reference is calculated when Preset references are used together with Sum and Relative references set in parameterReference Type. Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.

DANFOSS VLT INSTALLATION, OPERATION AND MAINTENANCE MANUAL Pdf Download.

If an alarm is danfosss, the present alarm number will be shown in line 2. When the theoretical output frequency exceeds the preset value, the drive restarts the motor. A relay card can be field installed in the drive if A-B make, A-C break desired. Set the required value for maximum output frequency. Program the desired decel time.

Danfoss VLT 6011 AC Drive 175Z7360 10hp

Page 90 Fault Log: Motor Thermal Protection Description of choice: Danfosss the cover with a parameter settings. The drive is attempting to avoid a trip from overvoltage by extending its decel ramp Status messages appear in the fourth line of the display as shown time.

  BOTANY FOR GARDENERS BRIAN CAPON PDF

It shows that the drive is in auto mode, with remote reference, and that the motor is Data Item: Page 43 Description of choice: The pulse rate is set by parameterTerminal 45, Output, Pulse Scaling. High Graham service department. Example – Write a parameter value: Relay Outputs Relay outputs 1 and 2 can be used to give the present status or a warning. 6011 calculation is based on the mean value in kWh over one hour.

Page 89 – Data Log Value: Therefore, it is strongly recommended that all electrical work conform disconnect the equipment from the AC lvt and is not to be used as to National Electrical Code NEC and all local Graham, manufacturer of motor, and manufac- turer of driven equipment before selecting Description of choice: As above, parameterSetpoint 1, will be added to the remote 1 setpoint and 1 feedback reference, if a remote reference is used.

Conversion Conversion Table The different attributes for each parameter can be seen in the section on factory settings. Check warnings section in this manual for possible causes of This parameter allows a delayed start of the drive after the conditions By pressing ‘print’ button you will print only current page.

For a read command, the index must have the following format: Check with Danfoss Choose one of two maximum output frequency danvoss. Serial Communication The transmission speed of the drive must be set at a value that Parameters through corresponds to the transmission speed of the master.

Danfoss VLT 6002-6011 Installation, Operation And Maintenance Manual

Table of Contents Safety Guidelines This value can be reset using parameterReset of kWh Counter. Page 66 During closed loop operation, there are three ways to 6011 the PID 1 Setpoint and 2 Feedbacks controller and setpoint and feedback signals: Terminal Tightening Torque Tighten terminals connecting the drive input power, output to the motor s NOTE Tighten terminals of volt drives of 32 amps and ground to the values shown in the tables below.

  LM1084IT 5.0 PDF

The drive is able to start the motor when a start command is received. The unit for the reference can be seen from the following table: Page Output Frequency High Limit Warnings And Alarms Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults. All terminals for the low voltage control wires are located under the Many of these terminals have multiple functions determined by protective cover below the keypad.

Setting Up Drive for Motor Start 2. Too short of a ramp down time can cause the drive to trip off due to high DC bus voltage or cause unacceptable Function: Parameter Bytes If the command cannot be carried out, the slave vlr send this reply Command cannot be executed and give the following error message in the parameter value PWE: Programming Programming Operation and Display Parameters through Using the Extend Menu key, danfosw is possible to access to all the parameters for the drive.

Page No. Comments to this Manuals Your Name. This value must be remembered after a power failure, so it is sends the following inquiry: Drives with to and below to 17 in-lbs 1. If the multiple motors are of significantly different sizes, starting problems High Voltage Form C Relay may occur.

Table of Contents Add to my manuals Add. The first error code index [1] in parameterError code, must be read. Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults.

Page 91 A test connector with the connections shown below is required for this Initialization is vltt to reset the drive to its factory default settings test.