Buy Gefran PID Temperature Controller, 96 x 48 (1/8 DIN)mm, 2 Output Relay, V ac, V ac Supply Voltage ON/OFF RR Browse our. setting up the Gefran controller for the application referenced above. Additional software and hardware configuration information can be found in the User’s. Gefran controllers are built with SMT technology. The instrument provides a complete operator interface, protected by a Lexan® membrane that ensures.
|Published (Last):||1 January 2012|
|PDF File Size:||16.98 Mb|
|ePub File Size:||11.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
For more information click here. Display Modification SP, alarms SP, alarms SP, alarms By adding the following amounts to gefraan values shown in the table a series of supplementary functions can be enabled: In this way, you just have to set the setpoint and the alarm, then launch self-tuning with the specific button. When it is switched on again a self- illegible diagnostic test is performed that checks intermittent start up of all the segments displays the value Clicking on a tag will display a list of all products gefraj that tag applied.
S Minimum limit of main input scale Min Keep to return immediately to level 1.
R Variable to compare Alarm setpoint A3. Dimensions And Cut-out Example: Input Virtual instrument inputs S. Comments to this Manuals Your Name.
Gefran 1200 Instructions For Use Manual
Output Virtual instrument outputs S. It continuously reads system oscillations, immediately seeking the PID parameter values that reduce the current oscillation. The instrument provides up to 4 outputs: R Select reference signal for alarm i.
It is enabled by means of configuration code AL. Accuracy better than 0.
Gefran PID Temperature Controller | Thermon Africa
By pressing ‘print’ button you will print only current page. If one or more segments do not light up contact your Gefran dealer.
An additional output 24VDC, 30mA max. This manual also for: Manual Tuning If the Integral Time value is too long Weak integral actiondeviation between the controlled variable and the set- point may persist. Cencal Memory Map – In addition to the control and alarm outputs, you can also have outputs that repeat the state of the digital or retransmission input by process variable, setpoint, deviation, alarm trip points and values acquired via serial line. Acquisition of the input signal msec. Manual Tuning A Enter the setpoint at its working value.
The instrument’s entire programming procedure is made easier by grouping the parameters in function blocks CFG for control parameters, Inp for inputs, Out for outputs, etc. Navigating Through The Controller Menu Navigating through the Controller Menu Keep pressed down to scroll through the menus in sequence and release it when the required menu appears.
GEFRAN INSTRUCTIONS FOR USE MANUAL Pdf Download.
Universal input configurable from faceplate Obtain perfect control by activating autotuning via button on faceplate, making commissioning very easy: Alarm 1 Alarm 2 Alarm 3 AL. LEDs will flash when softstart or autotuning are in progress or when a sensor fault occurs Trigger pre-configured control functions alarm reset, Auto Manual mode… via remote switch.
Example of connection with TC input. Instrument identification code [ It is particularly in combined Heat-Cool control applications where the advanced algorithms come into play, allowing an extremely narrow band between heating and cooling gevran causing overlap.
It does not engage if the oscillations drop below 1.
Lexan that guarantees IP65 level protection. Notes concerning electrical safety and. Integral heating time [0. An analog output in voltage or in current is also available.
During the test, all the display segments and the 7 indicator lights will flash. N disabled disabled disabled enabled disabled disabled Gefraan number of enabled alarms disabled enabled disabled enabled enabled disabled disabled disabled enabled enabled disabled enabled disabled enabled enabled enabled enabled enabled By adding the following figures to the value in the table it is possible to enable a series of supplementary functions: InP Input settings third menu to set gefram This menu makes it possible to configure the parameters for the Controller input signals.
In addition to the control and alarm outputs, you can also have outputs that repeat the state of the digital or retransmission input by process variable, setpoint, gefra, alarm trip points and values acquired via serial line. Choose from a wide range of software-selectable inputs, including V and mA.: