LAN High-performance Quad Operational Amplifier. The LA consists of four independent, high-performance, internally phase compensated. LAN datasheet, LAN circuit, LAN data sheet: SANYO – High- Performance Quad Operational Amplifier,alldatasheet, datasheet, Datasheet search. LAN Datasheet PDF Download – High-Performance Quad Operational Amplifier, LAN data sheet.

Author: Mumuro Moogujar
Country: Vietnam
Language: English (Spanish)
Genre: Video
Published (Last): 27 February 2008
Pages: 111
PDF File Size: 18.10 Mb
ePub File Size: 18.38 Mb
ISBN: 800-3-76264-787-1
Downloads: 37577
Price: Free* [*Free Regsitration Required]
Uploader: Zulkilmaran

LAN (SANYO) PDF技术资料下载 LAN 供应信息 IC Datasheet 数据表 (1/5 页)

SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values such as maximum ratings, operating condition ranges, or other parameters listed in products specifications of any and all SANYO Semiconductor products described or contained datashet. No phase compensation required? The screen is split into a left half and a right half.

To verify symptoms and states that cannot be evaluated in an independent device, the dataeheet should always evaluate and test devices mounted in the customer’s products or equipment. This chip behaves exactly like a shift register, so data shifted into DIOI on the falling edge of the first clock la632n4 is shifted out of DIO64 at the 64th falling edge.

The voltages are all measured relative to logic low. The circuit board has seven large ICs and two smaller ICs. The remaining 4 are created by the quad opamp IC.

The scope output below shows the beginning of a row where the data is being datasjeet, corresponding to three dark pixels with a clear pixel on either side. Three are from header pins 7, 8 and, via the transistor, pin 9. In the event that any or all SANYO Semiconductor products including technical data,services described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law.

I’m a current participant in the great post-grad job hunt. It can be applied to various uses in commercial datasbeet industrial equipment including all types of transducer amplifiers and DC amplifiers. If you apply a DC voltage to a cell it will work but not for long. These four operational amplifiers are packaged in a single package. A few months ago I popped into Goodwill to see if they had any interesting electronics to take apart.


The circuit board the screen is attached to has a ten pin row of standard 0.

As in case of conventional general-purpose operational amplifiers, operation from dual power supplies is also possible and the power dissipation is low. The two halves are loaded in parallel and all the logic is the same for datasheett half.

Light passing through one polarizer is then rotated 90 degrees by the liquid crystal such that it lines up with the second polarizer. CDI1 is not shown since that pin is always held low. Until I get into the software we can ignore the right half of the screen and pretend there are only three column driver ICs.

The following steps go through the process of filling all three buffers. Unfortunately, things get a bit more complicated. Effect of Chirality and Twisted nematic field effect. The screen is split into two sections, each pixels wide. The next output still shows the same signals, but with the more realistic scenario where the rows are being activated one at a time while every pixel in every column is ON dark.

(PDF) LA6324N Datasheet download

Which voltage is output at any given moment is a function of the M level and the Q level corresponding to the electrode being ON or OFF. This output shows the somewhat unrealistic, but helpfully illustrative, case where every row and every column are ON at all times. CDI on the first IC of each set of three is pulled low.

I already had a few of the 16×2 character LCDs and a Nokia cell phone screen breakout board I could have used, but those are pretty small and I was intrigued by the idea of reusing this old display. This allows chaining to control displays with more than 64 columns.


Information including circuit diagrams and circuit parameters herein is for example only; it is not guaranteed for volume production. In this display O1 is connected to the top row and O64 is connected to the bottom row. Logic low Vss will be close to V3, but could be above or below it depending on the what the pot is set to since the pot controls VEE.

The numbers refer to the pin number in the headers pins. After googling for the datasheets it turns out that one of the smaller ICs is a quad opamp LAN which provides the required voltages for driving the LCD cells more on that later.

Wide operating voltage range: This catalog provides information as of October, The end effect of this is to change the screen contrast. The headers are shown as viewed in the picture of the back of the screen above. For a pixel to be OFF clear the voltage difference between the electrodes is 1. I am a physicist and engineer with a passion for understanding the universe and building new things.

Breathing new life into a screen salvaged from a Smith Corona electric typewriter. For the row driver the selected voltages are the same, but the not-selected voltages and V2 and V5. The total voltage difference across a cell is determined by the difference between the voltages output by the column drivers and the row driver.

When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.